⎝⎛星力捕鱼⎞⎠

⎝⎛星力捕鱼⎞⎠ page Company Profile ⎝⎛星力捕鱼⎞⎠ Product center Quality system marketing network After sales service Recruitment contact us
Flow meter series
Temperature instrument series
Pressure instrument series
Calibration instrument series
Level instrument series
Digital display instrument series
Transmitter instrument series
Wire and cable series
Bridge instrument cabinet series
Pipe fitting valve series

Address: Xiongyi, Jinhe Road, Jinhu County, Jiangsu Province
Lunan
Phone: 0517-86900901
0517-86900921
0517-86900920
Fax: 0517-86900902
Postcode: 211600
http://zzyfwh.com
Email: chinadongxiang@163.com
technical article
Common obstacles and treatment methods of gear flow meters
2012-2-16 9:43:48

的使用注意事项: 首先,按照要求正确安装后的椭圆齿轮流量计,使用时即可保证足够的精度,通常累计值的精度可达0.5级,是一种较为准确的流量计量仪表。 Precautions for the use of the intelligent elliptical gear flowmeter : First, the elliptical gear flowmeter after the correct installation according to the requirements can ensure sufficient accuracy during use, and the accuracy of the cumulative value can usually reach level 0.5, which is a more accurate flowmeter. meter. However, if the flow rate of the measured medium is too small during use, the effect of the leakage error of the instrument will be prominent, and sufficient measurement accuracy cannot be guaranteed. Therefore, the oval gear flowmeters of different models and specifications have an allowable value for the minimum used flow rate. The measurement accuracy can be guaranteed only when the actual measured flow rate is greater than the lower limit flow rate allowable value. Secondly, when using an elliptical gear flowmeter, pay attention to the temperature of the measured medium must not be too high, otherwise it will not only increase the measurement error, but also may cause the gear to jam. For this reason, the oval gear flowmeter is used within the operating temperature range specified by the meter. After long-term use, the gears inside the oval gear flowmeter will be corroded and worn, which will affect the measurement accuracy. Therefore, it is necessary to pay attention to observation and take off regularly for inspection. If conditions permit, it is better to perform calibration regularly.

由于属于比较精密的仪器,容易出问题的地方大多是在内部,因为内部有齿轮工作,齿轮对流动液体的清洁度有要求。 Oval gear flowmeters are relatively sophisticated instruments, and most of the problem-prone parts are inside, because there are gears inside, and the gears have requirements for the cleanliness of flowing liquids. It is easy to be stuck, and there are problems such as no display or large display fluctuation. The common faults and processing methods are as follows: 1. The degree on the display remains at a certain value. The fault processing method: first determine whether the signal feedback system is faulty. Turn off the power and check whether the signal feedback loop is on and whether the voltage is normal. If the fault is not removed, you can clean the pipes and filters. If the filter or pipeline is damaged, the flow meter can be disassembled and inspected to remove impurities. When disassembling, remember the entry points of the upper and lower gears, and install them as they are. 2. The degree is unstable on the display, and the troubleshooting method is to check whether the flow rate display system is vibrated; or turn the gear of the flow meter by hand to see if the display reading has changed. Generate a limited feedback signal. 3. When the flow is small, the error is relatively large, and the troubleshooting method may be that the gear sleeve is worn or corroded by the medium, and the flowmeter casing is deformed. At this time, you can generally hear a clicking noise when the flowmeter is working. 4. The error is very large or small. Actually, the troubleshooting method is because the fluid may contain gas, or the zero signal voltage is abnormal. Need to stop the operation to recalibrate the flowmeter. 5. There is a leak in the liquid. Fault handling method: If there is a leak, the fault must be caused by the aging of the seal ring. Just replace the seal ring.

:容积式流量计的一种,特别适合于重油、聚乙烯醇、树脂等粘度较高介质的流量测量,所以椭圆齿轮流量计一般也称油表。 Oval gear flowmeter : a type of volumetric flowmeter, especially suitable for heavy oil, polyvinyl alcohol, resin and other high viscosity medium flow measurement, so the elliptical gear flowmeter is also commonly called oil meter. The elliptical gear flowmeter is a purely mechanical principle flowmeter. It is completely intrinsically safe and suitable for various dangerous situations. The on-site display and remote transmission of the pulse transmitter are optional. Corrosion resistance, suitable for chemical and food hygiene industries. Oval gear flowmeters are extremely easy to install and maintain with accuracy levels of 0.3 and 0.5. Oval gear flowmeter: a type of volumetric flowmeter, especially suitable for heavy oil, polyvinyl alcohol, resin and other high viscosity medium flow measurement, so the elliptical gear flowmeter is also commonly called oil meter. The elliptical gear flowmeter is a purely mechanical principle flowmeter. It is completely intrinsically safe and suitable for various dangerous situations. The on-site display and remote transmission of the pulse transmitter are optional. Corrosion resistance, suitable for chemical and food hygiene industries. Oval gear flowmeters are extremely easy to install and maintain with accuracy levels of 0.3 and 0.5.