⎝⎛星力捕鱼⎞⎠

⎝⎛星力捕鱼⎞⎠ page Company Profile ⎝⎛星力捕鱼⎞⎠ Product center Quality system marketing network After sales service Recruitment contact us
Flow meter series
Temperature instrument series
Pressure instrument series
Calibration instrument series
Level instrument series
Digital display instrument series
Transmitter instrument series
Wire and cable series
Bridge instrument cabinet series
Pipe fitting valve series

Address: Xiongyi, Jinhe Road, Jinhu County, Jiangsu Province
Lunan
Phone: 0517-86900901
0517-86900921
0517-86900920
Fax: 0517-86900902
Postcode: 211600
http://zzyfwh.com
Email: chinadongxiang@163.com
technical article
The upstream and downstream inlets and outlets of plastic tube float flowmeters should ensure straight pipe sections of caliber
2012-4-7 11:09:39

有较好的耐腐性能,而且结构合理、体积也小,而且还很轻巧方便携带、不易破碎,一般都用于在化工、环保、食品等工业部门。 Plastic tube float flowmeter has good corrosion resistance, reasonable structure, small size, and is very light and easy to carry, not easy to break. It is generally used in chemical, environmental protection, food and other industrial sectors.
The installation problems of the plastic tube glass rotor flowmeter are analyzed as follows:
1. The plastic tube float flowmeter must be installed vertically. There should be no obvious tilt. The installation height should be convenient for reading the float. When reading, the line of sight and the float should be horizontal. [General standard: The optimal flow rate required is 50% -70% of the maximum flow rate of the flow meter. Try not to use the highest number. ] 2. Before using the plastic tube float flowmeter, take out the foam support inside the flowmeter with tool nose pliers and then reinstall it. When installing, pay attention to whether the rubber gasket is installed. In the takeover slot to prevent water leakage. 3. At the upstream and downstream inlets and outlets of the plastic tube float flowmeter, a straight pipe section with a diameter of 5 times that of the plastic tube float flowmeter should be guaranteed. 4. The pressure of the side fluid must be stable. If the fluid is too unstable, it will cause the float to fluctuate and cannot be measured correctly. A buffer or a setter should be set upstream of the flow meter. 5. The plastic tube float flowmeter should be installed vertically. The angle between the centerline of the flowmeter and the plumb line should not exceed 5 degrees. 6. The interface of the flowmeter can be matched with ABS plastic pipe, or PVC plastic pipe, bonded with special glue, or connected by plastic method, and then connected to the metal flange.


Plastic Tube Rotary Flowmeter Baidu Newsletter III === Online Article-For [Plastic Tube Rotary Flowmeter] 3 new results are provided ===

价格报价- 中国供应商 Plastic tube float flowmeter, plastic tube float flowmeter price quote-China suppliers
223 messages ...
Chinese suppliers provide free supply information of various plastic tube float flowmeters. You can also display and sell plastic tube float flowmeters for free here, and have the opportunity to pass your plastic tube float flowmeter products through various ...


Plastic tube rotor flowmeter, plastic tube rotor flowmeter price, plastic tube rotor ...-Global Hardware Network
LZB-S plastic tube float flowmeter is light weight, corrosion resistant, not easy to break, non-toxic and tasteless, easy to use, mainly ...
Appearance and installation dimensions LZB plastic flowmeter / LZS plastic tube float flowmeter / PVC plastic flowmeter price Jinhu ...


,lzs系列。 Flow meter | Flow meter company _Page 10_Shunqi.com Our factory specializes in the production of plastic tube float flow meters , lzs series. ...
Metal tube float flow meter lz series, simple structure,
Reliable work, wide range of application, with local indication, remote transmission, anti-corrosion and explosion-proof types, widely used in ...