⎝⎛星力捕鱼⎞⎠

⎝⎛星力捕鱼⎞⎠ page Company Profile ⎝⎛星力捕鱼⎞⎠ Product center Quality system marketing network After sales service Recruitment contact us
Flow meter series
Temperature instrument series
Pressure instrument series
Calibration instrument series
Level instrument series
Digital display instrument series
Transmitter instrument series
Wire and cable series
Bridge instrument cabinet series
Pipe fitting valve series

Address: Xiongyi, Jinhe Road, Jinhu County, Jiangsu Province
Lunan
Phone: 0517-86900901
0517-86900921
0517-86900920
Fax: 0517-86900902
Postcode: 211600
http://zzyfwh.com
Email: chinadongxiang@163.com
technical article
Use and maintenance of magnetic flap level gauge
2011-10-19 10:24:42

安装 磁翻板液位计 前, 将配套在液位计主导管外侧( 通常情况 贴有彩色标识) 校正磁钢取下 ,便于浮子能随着液位上下移动。 First, before installing the magnetic flap liquid level gauge , please remove the correction magnetic steel that is provided on the outside of the main pipe of the level gauge ( usually with a color logo ) , so that the float can move up and down with the liquid level. 将磁性浮子吸 住,以 防止浮子 搬远或 远输过程中 ,由于 上下移动 造成 液位计 损坏 Calibrating the magnetic steel is to hold the magnetic float to prevent the float from damaging the liquid level gauge when it is moved up or down .
安装 磁翻板 液位计 完毕后, 如果发现 磁翻柱翻转 颜色不一致 的时候 用校正磁钢吸顺 它。 Second, after installing the magnetic flap level gauge , if you find that the color of the magnetic flip column is inconsistent , please use the correction magnetic steel to suck it. 校正磁钢对磁翻柱引导 进行 液位计校正 红色 零位以下 显示 ,白色为零位以上 显示。 The magnetic column is guided by the calibration magnetic steel , and the level gauge is calibrated . Red is displayed below the zero position and white is displayed above the zero position .
投入 使用 磁翻板 液位计 避免介质液体 使的 浮子急速上升,造成磁翻柱翻乱 或者 翻转失灵 的现象出现 ( 通常 遇到此 现象, 重新 校正磁钢 进行 校正) 3. When the magnetic level gauge is put into use , in order to avoid the rapid rise of the float caused by the medium liquid , which may cause the magnetic flip column to be turned upside down or to fail , ( usually this phenomenon needs to be corrected with a magnetic steel calibration Correction ) . 液管 上引阀门, 然后再开启 液管 下引阀门, 这样 介质液体进入主导管 就比较 平稳 、安全。 We first open the leading valve of the liquid pipe , and then open the leading valve of the liquid pipe , so that the medium liquid enters the main pipe smoothly and safely.

In order for the magnetic flap level meter to measure accurately, we must also pay attention to the following points of maintenance:
为避免 浮子对 磁翻板 液位计 造成卡阻 减弱浮力 ,我们要定期检查, 固体杂质和磁杂质不 进入液位计筒体内 First, in order to prevent the float from blocking or weakening the buoyancy of the magnetic flap liquid level gauge , we must regularly check that solid and magnetic impurities must not enter the body of the liquid level gauge ;

定期 进行对 液位计主导管 清洗 ,不得有 沉积杂 质留在 管内 2. According to the condition of the medium, we should regularly clean the main pipe of the level gauge , and no deposited impurities should remain in the pipe ;  
进行 液位计 液体清洗 更换浮子 的时候,我们 打开排污法兰, 一定 注意重端带磁性一端向上,不能倒装浮子! 3. When cleaning the liquid in the level gauge and replacing the float , we open the drain flange, and we must pay attention to the magnetic end of the heavy end facing up, and the float cannot be inverted!