其传感器采用干式陶瓷压力传感技术，具有精度高、长期稳定性好、工作温度范围宽、抗载能力强、体积小，膜片面积大、不积物、可带现场指示器和不带现场指示器。 DEC-DBS301 flanged ceramic liquid level transmitter uses dry ceramic pressure sensor technology, with high accuracy, long-term stability, wide operating temperature range, strong load resistance, small volume, large diaphragm area , Without accumulation, with and without field indicator. Its process connection form is standard flange, flange material 1CrNi9Ti and polytetrafluoroethylene. DEC-DBS301 flange type ceramic liquid level transmitter has been widely used in various fields for the static pressure and liquid level measurement of corrosive media liquids, especially the pressure, liquid level measurement in the sanitary, food and viscous media industries. It can also be used to measure pressure parameters such as gas or steam.
● Main technical indicators Measurement range Relative pressure: 0 ～ 1.6MPa, -0.1 ～ 1.6MPa Minimum measurable ± 1KPa (100mmH20)
Static liquid level maximum liquid level height: 100m minimum liquid level height: 0.1m
Measuring diaphragm 96% alumina ceramic flange 1Cr18Ni9Ti polytetrafluoroethylene seal fluoro rubber fluorosilicone rubber
Ceramic is a recognized material with high elasticity, corrosion resistance, wear resistance, shock resistance and vibration. The thermal stability of ceramics and its thick film resistance can make its operating temperature range as high as -40 to 135 ° C, and it has high accuracy and stability for measurement. The degree of electrical insulation is> 2kV, the output signal is strong, and the long-term stability is good. High-performance, low-cost ceramic sensors will be the development direction of pressure transmitters.
厚膜电阻印刷在陶瓷膜片的背面，连接成一个惠斯通电桥（闭桥），由于压敏电阻的压阻效应，使电桥产生一个与压力成正比的高度线性、与激励电压也成正比的电压信号，标准的信号根据压力量程的不同标定为2.0 / 3.0 / 3.3 mV/V等，可以和应变式传感器相兼容。 Principle The anti-corrosive pressure transmitter has no liquid transmission. The pressure directly acts on the front surface of the ceramic diaphragm, causing the diaphragm to deform slightly. The flange-type ceramic level transmitter thick film resistor is printed on the ceramic diaphragm. On the back side, it is connected to a Wheatstone bridge (closed bridge). Due to the piezoresistive effect of the varistor, the bridge generates a voltage signal that is highly linear and proportional to the excitation voltage. The standard signal is based on Different calibration of pressure range is 2.0 / 3.0 / 3.3 mV / V, etc., which can be compatible with strain gauge sensors. Through laser calibration, the sensor has high temperature stability and time stability. The sensor has a temperature compensation of 0 ～ 70 ℃, and can directly contact most media.
The transmitter is a variant of the DBS series. Available with and without field indicator. There are two types of process connection: G1 1/2 and G2 external threads.
The transmitter has high accuracy, long-term stability, wide working temperature range, strong resistance to overload, small size, flush diaphragm structure, no accumulation, no blockage, easy cleaning and convenient installation. It is widely used in various industries to measure the pressure of viscous liquids, gases, and steam, and is especially suitable for pressure measurement in the pharmaceutical, health, and food industries.
● Main technical indicators Measurement range Relative pressure Maximum measurement range 0-40MPa Minimum measurement range 0-1KPa Absolute pressure Maximum measurement range 0-40MPa
Minimum measurement range 0-1KPa Negative relative pressure Maximum measurement range -1 ～ 2.4MPa Minimum measurement range -1KPa ～ 1KPa
◆ Measurement range
Relative pressure: 0 ～ 1.6MPa, -0.1 ～ 1.6MPa
Minimum measurable ± 1KPa (100mmH20)
◆ Hydrostatic liquid level
Maximum liquid level height: 100m
Minimum liquid level height: 0.1m
◆ Measuring diaphragm
96% alumina ceramic ◆ Flange 1Cr18Ni9Ti PTFE ◆ Maximum liquid level height: 100m
◆ Negative relative pressure
Maximum measurement range -1 ～ 2.4MPa
Minimum measurement range -1KPa ～ 1KPa
◆ Structure and materials
Housing: film die-cast aluminum
Size: 70 × 70 × 130
◆ Standard flange: GB911.6-88
◆ Protection level: IP65
◆ Weight: 3.8Kg
HR301 Code Description Transmitter Type G Common
B intrinsically safe process connection material 1 stainless steel 316L
2 PTFE process flange form A DN50 L = 0mm PN1.6Ma 1Cr18Ni9Ti
B DN50 L = 50mm PN1.6Ma 1Cr18Ni9Ti
C DN50 L = 0mm PN1.6Ma 1Cr18Ni9Ti
D DN80 L = 50mm PN1.6Ma 1Cr18Ni9Ti
E DN50 L = 0mm PN1.6Ma Teflon
F DN50 L = 50mm PN1.6Ma Teflon
G DN80 L = 0mm PN1.6Ma Teflon
H DN80 L = 50mm PN1.6Ma Teflon sealing material F Viton
P fluorine silicone rubber
Y agreed special output signal 0 0-20mA
Live display N No live display meter
A with on-site display meter accuracy level 2 0.25 level
5 0.5 measurement range (write directly for non-standard range) X See range code table
HR301 flange type ceramic liquid level transmitter has been widely used in the static pressure and liquid level measurement of corrosive media liquids in various fields, especially the pressure and liquid level measurement in sanitary, food and viscous media industries. It can also be used to measure pressure parameters such as gas or steam.
其传感器采用干式陶瓷压力传感技术，具有精度高、长期稳定性好、工作温度范围宽、抗载能力强、体积小，膜片面积大、不积物、可带现场指示器和不带现场指示器。 HR301 flanged ceramic liquid level transmitter. Its sensor uses dry ceramic pressure sensing technology, which has high accuracy, long-term stability, wide operating temperature range, strong load resistance, small volume, large diaphragm area, No deposits, with and without field indicators. Its process connection form is standard flange, flange material 1CrNi9Ti and polytetrafluoroethylene.
Jinhu Dongxiang Instrument Co., Ltd. is a comprehensive enterprise dedicated to the development, research, production, sales and engineering construction of industrial production process control instruments and automation systems. Its products are widely used in petroleum, chemical, power, metallurgy, brewing, water conservancy , Environmental protection and other industries. Since its establishment, the company has always taken the revitalization of the national instrument industry as its mission. In the unremitting exploration and practice, it has gathered a team of senior instrument engineers and experts, accumulated rich experience, and introduced advanced foreign technology and technology from the 1990s. device. After diligent and realistic, continuous innovation, we have formed a complete series of production scales including field instruments, panel-mounted instruments, measuring instruments, wires and cables, instrumentation pipe fittings, instrumentation valves and so on. At the same time, in order to satisfy user needs, we also represent the products of well-known foreign companies in the United States, Japan, and Germany. In terms of quality, it passed the ISO9001 quality system certification. With its strong technical force, advanced production equipment, complete testing methods, accurate and reliable products, and perfect after-sales service system, the company has won the trust of many users.
Integrity-seeking truth from facts, providing customers with practical service innovation-independent innovation, focus on leapfrogging, supporting development, leading future quality-casting brand with quality and strengthening products with service Jinhu Dongxiang Instrument welcomes new and old customers' inquiries, and is willing to become a good partner for your cooperation with efficient and high-quality services. Let us cooperate sincerely to create brilliant.